Fluke 773 Clamp Meter, 100mA dc

772 & 773 Milliamp Process Clamp Meters Need more hours in your day? Save time by not breaking the loop on 4-20 mA signal measurements with the Fluke 771 Process Clamp Meter. Are you spending time: •Taking mA measurements by removing a wire and breaking the loop •********* loop •Testing analog input/output on a console •Troubleshooting devices with mA inputs and outputs •Repai********* oops •Going back to the shop to get extra tools If you need more time in your busy day take a good look at the Fluke 772 and 773 mA Clamp Meters. Designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system. Here are some specific ways the Fluke 772 and 773 clamp meters will help you: Measure mA signals for PLC and control system analog I/O without breaking the loop •Measures low level dc current •Correlate process indication with real physical value Measure output signals from transmitters without breaking the loop •Maintain and troubleshoot process and automation equipment without breaking the loop •No disruption to the process Detachable clamp with extension cable •Measurements in tight locations •Enables measurements in difficult situations Measurement Spotlight •Illuminates hard to see wires in dark enclosures •Measurement process is easier and quicker Measure up to 99.9 mA range non-contact •Wide range of measurements •Measures 10 to 50 mA signals in older control systems Automatic power off •After 15 minutes and 2 minute automatic off for backlight and spotlight •Saves battery life Want simultaneous mA source/measure? Consider the Fluke 773 Milliamp Clamp Meter. Features and Benefits •Best in class 0.2% accuracy •0.01 mA resolution and sensitivity •Measure 4 to 20 mA signals without “breaking the loop” •Measure mA signals for PLC and control system analog I/O •Dual backlit display with both mA measurement and percent of 4 to 20 mA span •Measurement Spotlight illuminates hard to see wires in dark enclosures •Detachable clamp with extension cable for measurements in tight locations •Measure 10 to 50 mA signals in older control systems using the 99.9 mA range •Automatically change the 4 to 20 mA output for remote testing •Power saving features, auto-off, backlight timeout extend battery life •Hold function captures and displays changing measurements •Measure 4 to 20 mA signals with in-circuit measurement •Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters •Source 4 to 20 mA signals for testing control system I/O or I/Ps •mA output linear ramp or 25% step output •Automatically change the 4 to 20 mA output for remote testing Fluke 772 additional features: Source 4 to 20 mA signals for testing control system I/O or I/Ps Simulate 4 to 20 mA signals for testing control system I/O Measure 4 to 20 mA signals with in-circuit measurement Simultaneously measure mA in-circuit with 24 V loop power for powering and testing transmitters Source mA output signals in a linear ramp or 25 % step output for remote testing Power saving features, auto-off, backlight timeout extend battery life Fluke 773 additional features: DC voltage measurement to verify 24 V power supplies or voltage I/O signals Source dc voltage to test input devices that accept a 1 to 5 volt or 0 to 10 volt signal Scaled mA output corresponds to the 4 to 20 mA signal measured by the mA clamp enables a logging DMM or other device to record the 4 to 20 mA signal without breaking the loop mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal Voltage output linear ramp or 25 % step output Automatically change the voltage output for remote testing Comparison Table Model mA measure w/jaw mA measure in circuit mA source mA sim Loop power 24 V DCV source 0-10 V DCV measure 0-30 V Scaled mA output to mA inpu mA in/out 772 x x x x x - - - - 773 x x x x x x x x x Model Function Resolution and range Accuracy Notes 772 and 773 mA measurement 0 to 20.99 mA 21.0 to 100.0 mA 0.2 % + 2 counts 1 % + 5 counts Measured by clamp 772 and 773 mA measurement 0 to 24.00 mA 0.2 % + 2 counts Measured in series with test jacks 772 and 773 mA source 0 to 24.00 mA 0.2 % + 2 counts Maximum mA drive: 24 mA into 1000Ω 772 and 773 mA simulate 0 to 24.00 mA 0.2 % + 2 counts Maximum voltage 50 V dc 773 Voltage source 0 to 10.00 V dc 0.2 % + 2 counts 2 mA maximum drive current 773 Voltage measure 0 to 30.00 V dc 0.2 % + 2 counts - Note For details of the 771 process clamp meter see stock no. 287-642 Supplied with 4 AA alkaline batteries, test lead set with integral prods and 2 crocodile clips; test leads with integral grabber clips; soft carry case & instructions

Fluke 773 Clamp Meter, 100mA dc

Location: Sydney 25 Pavesi Street Smithfield NSW 2164

N/A

When you call, Don't forget to mention ADSCT whenever you will call to user. Be safe during payment.